The short answer

A sofa fits through a straight doorway as long as one of its sizes, its height, its depth or its diagonal depth, is smaller than the narrowest gap on the route, and the sofa can be turned to present that side.

The pinch point is usually an internal doorway rather than the front door. The usable gap is smaller than the nominal frame size because the open door, the door stops and the hinges all take a share of the space, meaning standard measurements often flatter the actual opening.

This is the check we run before a move is quoted, in the order a sofa travels: pavement first, room last. Each opening on the route gets a pass, a borderline or a fail, and a single fail anywhere between the kerb and the sitting room decides the job.

Twenty minutes with a tape measure, a notebook and a phone camera gives you that answer before the van is booked, instead of while it sits outside.

Moving house or flat? If the sofa is already in your living room, it most likely came in through the same route, so taking it out is usually straightforward. The route to check is the new home, which the sofa has never been through. The same goes for a sofa that went through a previous move or delivery without trouble. If you are unsure, just ask us.

How to find the narrowest point on your route

A sofa is only as movable as the worst gap on its route. Measure every doorway, corridor and turn as a separate result, then identify the point that controls the whole move. One generous hallway does not cancel out a tight door frame.

A person using a tape measure to check the clear usable width of an open doorway in a London home, measuring between the

Standard internal doors in UK homes are often around 762 mm (2 ft 6 in) wide, but older properties vary a lot, so the measured gap matters more than the size the door was sold as. Once the open door, the door stops, and the hinges and nearby furniture are counted, the clear passage shrinks further.

Measure the gap, not the frame. Tape from the door stop to the face of the open door at the narrowest point, then forget the size the door was sold as.

– Open the door to a full 90 degrees, checking that a door closer, thick carpet or an obstruction does not stop it earlier.
– Measure from the door stop or frame to the face of the open door at its narrowest point, in millimetres.
– Measure the opening height from the floor to the underside of the frame.
– Measure the hallway or landing beside the door, including the space available to angle the sofa into the opening.
– Photograph each reading with the tape visible in shot, so nobody has to guess later whether it was 748 mm or 784 mm.

Give each opening its own result rather than averaging the route. A pass means the sofa can move through without changing the doorway. A borderline result means taking the door off its hinges or changing the carrying angle may decide it. A fail means the fixed structure is too restrictive even with the door removed.

Taking the door off its hinges can gain a centimetre or two, but hinges, skirting boards, radiators and bannisters can still reduce the working space. Where two openings are equally tight, the one with the poorer approach angle governs the route.

Will the sofa fit around corners and in lifts?

A doorway is one item on a list of seven, and the sofa has to pass all of them. Walk the route in travel order:

  1. The gate or communal entrance. Conversions often have a shared front door narrower than the flat’s own.
  2. The front door. Check the threshold and any step, because a raised lip changes the angle you can hold.
  3. The internal doorway to the destination room. Measure it even when a wider one nearby looks more inviting.
  4. The hallway and any 90-degree turn. Length matters more here than width.
  5. The staircase, measured at its narrowest point, between the wall and the handrail or bannister, not wall to wall.
  6. Landings, plus the ceiling height above each turn. A sofa rotating on a landing needs headroom as well as floor.
  7. The lift. Record the interior and the lift door separately, because the cab is often roomier than its opening.
A sofa being carefully manoeuvred around a tight landing turn in a London flat, with two movers checking the clearance n

Then the rotation rule. Where a doorway is too narrow for the sofa to go through sideways, it can sometimes go through standing on its end, with its length pointing up, and in that case the doorway height has to exceed the sofa’s arm-to-arm width. Standing it on end also helps at a tight turn, because it takes up far less floor than a sofa swinging flat. Bannisters matter for the same reason: if the sofa must be lifted over one, the gap between bannister and ceiling needs to be greater than the sofa’s smallest dimension.

The turn test. If the sofa has to rotate through 90 degrees, corridor width alone tells you nothing. You need the floor space to swing the full length through, which is why landing dimensions go on the list next to door widths.

London flats add layers a house does not have. Shared entrance doors, narrow communal corridors, lifts that need booking and heavy fire doors that swing shut mid-carry can each become the governing dimension. A sofa can sail through a straight doorway and still fail at a turn, because its length, not its cross-section, sets the space needed to rotate.

When we plan a move we look at access, lift availability, floor level and parking before choosing the vehicle, crew and time. Moves through shared stairwells and lifts are quoted on the route as much as on the contents, which is where our flat removals in London start. Our house move service in London starts from exactly that assessment.

Measure the sofa and run the clearance test

The brochure leads with the length, but at a straight doorway the length hardly matters, because the sofa travels end first. What passes through the frame is the sofa’s profile: its height, its depth and its diagonal depth. The length comes back into play at turns, on stairs and in lifts.

Measure the four numbers that matter

Use a tape and a notebook, and round up rather than down.

  • Width, arm to arm. It does not matter at a straight doorway, but it decides whether the sofa can turn a corner, fit in a lift or stand on its end under the ceiling.
  • Depth, front to back. At the deepest point with the cushions on, then again with them off.
  • Height, floor to the highest fixed point. Record it with the legs fitted and with them removed.
  • Diagonal depth. Hold a straight edge from the top of the back to the front of the arm (or the front edge of the seat frame on armless styles), then measure from the bottom rear corner to that straight edge at a right angle. Because a sofa is L-shaped in profile, this figure is usually smaller than both the height and the depth.

You do not need every number to clear every opening. If the sofa’s smallest side is 60 cm and the gap is 68 cm, that side goes through, as long as the sofa’s other dimension clears the height of the opening. The diagonal depth only becomes the deciding figure when both the height and the depth are larger than the gap, because it tells you whether the sofa can be angled round the frame. At a straight doorway a long, shallow sofa often passes where a short, deep one cannot, which is why comparing lengths with door widths catches people out. Note which legs, feet, arms or back sections detach and by how much each one shrinks the sofa. A fixed back and non-removable feet are the two details that most often turn a comfortable fit into a fail.

If the sofa is delivered boxed or wrapped, compare the packaged dimensions with the route as well as the assembled ones. The box has to clear the gap in both directions, and the floor-to-ceiling height above any tight turn needs checking too.

Run the comparison at every opening

Set the sofa’s figures against the readings from each doorway and compare the right pairs:

  • Smallest dimension against the clear width. One of the sofa’s sizes, the height, the depth or the diagonal depth, whichever is smallest with the legs off, must be smaller than the clear width at the narrowest gap, measured with the door open as far as it will go rather than as far as you would like. Leave room for hands.
  • The upright side against the opening height. Whichever side travels vertically has to clear the height of the opening, including headroom on a stair.
  • Arm-to-arm width against turns, lifts and ceilings. At a 90-degree turn or in a lift, the sofa’s full width has to fit the floor space. If it has to stand on its end, the ceiling must be higher than that width, with extra room to tip it up.
  • Packaged size against the narrowest point, in both directions, if it travels boxed.

Then think through the actual route, including door swing, skirting, radiators, bannisters, turns and landings. A sofa can pass a doorway comfortably and fail at a 90-degree turn because the landing cannot take its width, which is common in London flats where the entrance is generous and the communal landing is not.

Set the margin before you classify

A pass means the sofa’s governing measurement sits clearly under the opening once packaging and hands are accounted for. A borderline result means it is close at the tightest point, which is a cue to arrange a survey rather than to hope. A fail means that none of the height, the depth or the diagonal depth, with the legs off, clears the narrowest gap, or that the sofa’s width cannot make a turn on the route. A fail on the fixed measurements is not always the end of it: most bulky sofas can be dismantled, and a sofa that cannot be taken apart may still go in through a window, as explained below.

Allow for protective blankets and hand clearance, and treat upholstery compression as a small tolerance only, never as a guaranteed reduction. Test the sofa in the orientation it will travel, because many upholstered models go through upright or on their side.

Plan parking and building access in London

A parking suspension buys kerb space. It does nothing for a narrow communal corridor or a lift that closes early, so treat it as one line on the plan rather than the plan itself. Many London councils let residents reserve space or request a suspension for a house move, and the application process, notice period and fees vary by borough, so check your own council before the vehicle is booked. We explain how it works in our guides to parking suspension when moving house in London and parking suspension and dispensation.

A London removals van parked legally at the kerb outside a residential block of flats, with two movers checking the buil

The building side needs the same attention:

  1. Confirm lift booking and access hours with the building manager, including any evening cut-off.
  2. Ask whether communal doors can be held open during the carry, and who holds the keys or fob.
  3. Ask the building manager about any notice needed for fire doors or protected entrances, particularly in mansion blocks and listed buildings.
  4. Note the controlled parking zone and its time windows for the day itself. Our guide to controlled parking zones in London explains how they work.

Book in this order. Lift first, then the suspension, then the vehicle. Each one fixes the next, and the carry cannot start before the sofa can reach the door.

Keep a copy of any approval with you on the day. Our moving house checklist helps you slot these bookings into the wider timeline.

What to do when the sofa is borderline

The instinct is to push harder, and that is the one move that turns a tight fit into a torn frame and a gouged wall. A borderline result is not a no. It is a prompt to choose deliberately between five options.

  • Strip the sofa back. Most large and bulky sofas can be partly dismantled. Legs, arm sets, back sections and cushions often come off, and each one that does reduces the size you are measuring. Take them off first, then retest the height, the depth and the diagonal depth. If the sofa is wider than the door frame, we dismantle it, carry the sections through and reassemble it in the new room. It is the cheapest change available and often the one that settles it.
  • Take a door off its hinges, where permitted. Removing the door can give you an extra centimetre or two, which is sometimes all a borderline sofa needs, and we can take it off and refit it on the day. In a rented flat, ask the landlord or managing agent first; in a communal area, ask the building manager. Label the hinges, bag the screws and tape them to the door.
  • Split it. A modular sofa separates into sections that each pass the route on their own, which removes the turning problem completely.
  • Check the window route. If the sofa is wider than the door frame and cannot be dismantled, we check whether it can be hoisted through a window instead. That depends on the window opening, the floor level and the space outside, so it is something to raise at the survey rather than to assume.
  • Stop and change the plan. Store it, return it or arrange a different access route. If storage buys you time while access is sorted, see our guide to storage units in London, or compare short-term self storage prices before committing to a unit size.

Dismantling is only worthwhile if the sofa goes back together properly, which is why we take it apart and reassemble it ourselves rather than leaving it to chance. Look at the fixings before you start. Bolts and cam locks are a different proposition from glued dowels. If a piece rebuilds better with a second pair of hands, see our flat pack furniture assembly service.

Protect frames with boards or blankets, and never force a sofa past a tight bend. A doorway that leaves no room to grip, pivot or protect a surface turns a two-person carry into a scrape along a wall, even when the sofa is technically small enough to pass.

This is general guidance. Tenants should get permission before removing a flat entrance door, altering anything communal or dismantling a landlord’s furniture, and should photograph the existing condition of frames, walls and skirting before anything moves.

Book a survey before you confirm the delivery

Three situations justify a survey rather than a tape measure and a guess: a borderline result at the tightest point, a turn or a lift on the route, or a sofa with detachable parts you are planning to take apart.

Our pre-move survey is done by WhatsApp video walkthrough or in person, and its purpose is to look at the items, the access and any special handling in one pass. The route and the load get assessed together, and the quote that follows is a fixed price.

What helps us at the survey

You do not need all of this to get in touch. If the sofa came in without trouble or has been through a move before, just tell us and send a photo or two. For a tight or unfamiliar route, the details below help us give you a firm answer sooner:

  • Millimetre figures for every opening on the route, photographed with the tape in shot.
  • The sofa’s width, height, depth, diagonal depth and packaged size.
  • Whether the sofa can be dismantled, which parts (legs, arm sets, back) come off, and how much each one reduces the size.
  • Window size and floor level, if a window route might be needed.
  • Lift details, floor level and the parking plan.
  • Photographs of each restriction, including the turn and the landing above it.

Photographs first, measurements if you have them, then the survey, then the delivery date. If the sofa is only one item among many, a man and van may cover a small move, while a full home move is better planned through our house removals service.

If you would rather have the route checked by the people carrying the sofa, Best London Removals Ltd has covered every London borough from our Ruislip base since 2011. Send us a few photographs of the tight spots, with measurements if you have them, and we will arrange a survey by video or in person. Visit Best London Removals Ltd to book it before the delivery date is fixed.